팝업레이어 알림이 없습니다.
The world's strongest surface protection coatings
ALL PRODUCTS |
ANTI FOG COAT
KILL VIRUS COAT
ANTI FOG COAT
KILL VIRUS COAT
You can become a coating expert if you refer to the FAQ board before coating on your vehicle.
After coating, which shampoo should I use for washing? Can I use foam gun?
You can use any kind of a shampoo, but you do not need to clean with the shampoo.
Unless your vehicle is very dirty, just spraying water with a hose, and then clean up with a MF towel or a wool wash mitt, may be sufficient to clean your car.
You can see how Aquartz can protect the surface from strong acid.
Is Clean Air odor eliminator harmful to health?
If you are referring to AQuartz Clean Air; it is not a perfume but rather a coating agent.
Previous technology TiO2 coating products were bonded with Sulfuric Acid, which was harmful to health and stained easily.
AQuartz Clean Air is new technology eco-friendly, water based coatings and therefore not harmful to health.
If you are you aware of “Sick House Syndrome” which makes your eyes sting
and have a musty smell which is harmful to health, but after coating with AQuartz Clean Air,
the symptoms will go away.
AQuartz Clean Air is a very popular product in use in Korea.
A test report on AQuartz Clean Air can be found here:
Can I use T-Cera and Titanium V2 ,V3 on plastic surface?
You can coat AQuartz on car paint or windshield as well as plastic, glass, bathroom mirror,
LCD monitor, and even on ceramic urinal.
There is no problem on applying Aquartz on treated trim
Apply a coat of Aquartz on your computer monitor.
You will have fewer fingerprints and dust particles on the surface. The screen will remain cleaner for a longer time.
Why do we need to coat Top Coating on top of AQuartz PPF Base coating?
All painted surface has many micro-pores (pin-holes).
As a newly painted surface cures, the micro-pores are created from the air trapped in the paint.
And as time goes on, airborne chemical compounds, ferrous particles and dirt actually penetrate the paint,
and gets stuck in the pin-holes within the paint surface.
They create corrosive compounds that eat deep into the paint's sub-layers or paint's pin-holes.
In order to keep the original car paint colour in perfect condition for long time,
we have to cover the pin-hole and block UV rays with Aquartz Premium and Aquartz Titanium.
So we have to remove all contaminants from the surface before AQuartz can be applied.
Iron Cut or Clean Shot can be used to remove minor dirt easily.
After thoroughly cleaning the entire painted surface,
it must be covered up with AQuartz Premium Film before airborne chemical compound
and the ferrous particles penetrate into the paint surface.
But, Aquartz Premium is not sufficient enough coating to completely cover because it also has pin-holes.
As AQuartz Premium forms the pin-holes from air pockets also,
we require smaller nano-particles to cover the pin-hole of Aquartz Premium.
That is why we need to use AQuartz Titanium.
AQuartz Titanium covers the smaller pin-holes of AQuartz Premium.
To obtain the best results,
one layer is not sufficient to cover the pin-holes and block UV rays because it is too thin a layer.
For thicker Aquartz Premium coating and Aquartz Titanium,
you need to coat 2~3 layers of AQuartz Premium,
and 1~2 layers of AQuartz Titanium coating as a final detailing step.
The thicker Aquartz Premium and Aquartz Titanium coat will maintain your original car paint longer.
Is PPF coating applied in the same way as the Titanium V3?
Yes, it's the same application
What are some of the more popular applications for Clean Air liquid?
Unpleasant smell area; Hat, Socks, shoes, clothes, furniture and carpets, curtains, etc
What is the difference between CarPro Reload and AQuartz Reload Premium?
Carpro Reload is made in Japan, and AQuartz Reload is Korea, we manufacture AQuartz Reload.
If you want to buy Carpro Reload, you had better to do from Sensya-No-Oukoku Co., Ltd. Tel +0463-94-5106 Fax +0463-94-5108,
It called "Fine Cristal" car cleaner.
If you want to buy it from them directly, you should do it cheaply.
AQuartz Reload is water based, Carpro Reload is based alcohol.
AQuartz Reload is white colour, Carpro Reload is green.
AQuartz Reload is Titanium formula, Carpro Reload is oil.
Because Carpro Reload is not our product, we do not know about it well.
But AQuartz Reload is better known to be more long duration and self-cleaning effect by Titanium formula.
What is the differencce between your product and CeramicPRO 9h?
There's a big ingredient difference between the two.
AQuartz is water based with 50 nono-meter metal titanium.
After coating on the surface of a coin or plastics, AQuartz is not
able to come off the layer, but CeramicPRO is taken off it easily.
The power of adhesion, it is very important to long lasting.
Please check the truth with direct test, and ask CeramicPRO to show
you the abrasion certificate, not hardness certificate.
And we do not trust SGS certificate.
Do I have to apply Base PPF Coating first before Top Coating?
Although it's not required, it's the best way to protect your car paint for a long term.
PPF is a base layer for protect car paint from the outside damages
like a film cover, and Titanium, T-Cera and Reload are a top layer for the
effect of gloss, water-repellent, etc.
The Curing Time of Base Coat or Top Coat
Regarding the curing time.
- The basis of working temperature : 5~40 degrees Celsius (25℃ ).
- The higher temperature and lower humidity make a shorter curing time.
- The more it cures better protecting and water repellent it shows.
- For short curing time(30 min~1 h), If you use a heat gun or sun-lights, you can save the curing time in 5 min ~10 min to coat 2 layers AQ on the first layer.
- Completely cure with NO rain takes 24h.
- After PPF applying, the interval of top coating is about 1 hour if you do not use a heat gun.
- If you use a heat gun, after 20 min, you can apply top coating on the PPF layer.
- Dry the layer of top coating like drying your hair.
How to get the best hardness layer of coating
In order to get a best protection,
1. The surface needs 2~3 layers of the base coating or top coating first, and you try to apply top coating of 1~2 times at intervals of about three or four days.
2. Before you try to apply, you must remove all surface contaminants and wash and rinse off all the residue of cleaners thoroughly. The residue of cleaners make the hardness week.
3. After coating, you need to take plenty of time to dry the layer off completely for the sun and the air or with a heat gun or a hair drier, etc..
Do you recommend any of those products to be applied under the car for anti corrosion?
We do not want to do, our products are for car paint and glass on
Can T-Cera be applied more than once in a short period, for example every week?
It's very good maintenance to get the best thickness, durability and hardness
Why are watermark or hazy patches problem are risen?
PPF and T-Cera have very easy to applications.
Because the layer of PPF and T-Cera is for a film layer form after they dried, it does not produce kinds of hazy patches or watermark problem.
If they does, how can we coat them on glass(windshields)? They make acrystal clear film layer.
You might encounter these problems if you did not remove a kind of wax, silicone, oil, polymer, teflon, all the residue of cleaners thoroughly, before you apply AQuartz PPF, when you wash your car, or did not finis wipping job off with new microfiber towel.
A kind of a wax, Cqutarz, Silicone products, etc, they are easy to produce these problems when contact calcium water because of chemical reaction.
After the layer cured completely, it is difficult to remove it without mechanical wear . But You can remove it with Aquartz+ Plus, or 1500gr compound or Super Cut.
You can remove the layer of PPF with Super Cut.
For absolute beginners, we recommend you to use T-Cera.
What are the benefits of coating on the vehicle?
A simple example of the meaning of a coating is the same as the principle of placing a glass or protective film on a table to protect the table surface when we purchase a new table.
Protected by a glass or protective film, the desk protects the surface from scratches and scratches, so it can be used like a new desk for a long time, looks classy and can be cleaned easily if it gets dirty.
For this reason, if you cover a protective film or glass on your car, the surface of the car will be protected from scratches and you will be able to keep its brilliance for a long time and you also will be able to wash easily and simply.
In order to get the best results of the coating, the surface should be clean, free from scratches and free from any damage, so that it is best to coat it on a new clean car.
When coating on a used car, you must remove any scratches or foreign objects on it to make it look like a new car too.
If you coat it without doing them off, they will be seen through that layer of coating and it will become even more difficult to repair.
These surface repair works are called paint work, polish work, removing contaminants work.
These repairs are costly and it is difficult for the general public to do. It is best to have the coating done immediately, or at least within 3 months, when purchasing a new car.
Search your words